Collaboration and Cooperation

Lenny Kravitz could be considered one of the most iconic rockstars of the past ten years. His personal style/choice of clothing and retro sound have set him apart from many of the musicians out there today. (for example: watch this video It is a few years old, but it still captures well some of Kravitz's persona) 

This article discusses not only the collaboration between artist and lighting designer but also between lighting designer and set designer. Steve Cohen( Billy Joel, John Mellencamp, Blake Shelton, and Reba) was the LD for this tour with Es Devlin(Kanye West/Jay-Z, Muse, Shakira, Take That) was in charge of set design. The two designers for this tour did not meet until rehearsals for the tour had begun, so all of their communication had to be done through email and phone calls. The job of these two designers was to create a melding of set pieces and lights that would capture Lenny Kravitz's persona and also help support the music that was being performed on a nightly basis. I would say they did a pretty great job.

Steve Cohen mentions that he usually designs both the sets and the lighting for the shows he is a part of, so I can imagine that it may have been difficult for him to give up control of this part of the show. But maybe not Cohen says, "It's one thing to say you're a collaborator, another thing altogether to actually collaborate, and I learned, once again, that the sum is greater than it's parts"

The set that was designed by Es Devlin is the triangle screen spanning across the stage. She designed it in such a way that it would look as if it was infinite and according to Cohen it is a simple trick, but thought it may be simple, it is a trick that he is not allowed to share. Es Devlin talked with Kravitz the most at the onset of the design. Kravitz talked to Devlin about a "black glass mountainous installation" he had seen in Paris. Over the course of three days of face to face communication Devlin tried to understand the vision and then was confined to emails and telephone calls as the design became full fleshed out. 

When Devlin's design was combined with Cohen's lights it created the perfect look of a mountain that was seemingly never ending. I would think that were the lights not placed the way they were, the illusion would not be as convincing, but, if the set were not designed in such a way to have an illusion available to be worked with, there would be no reason for specific light placement. 

The overall point that I'm gaining from this is how important vision and communication are. They go hand in hand. If someone has a grand vision, but no way to communicate with others it will fail. If someone is great at communicating but has no vision, they will have nothing to communicate. It is incredible to see what can happen when two creative minds pour their energy into a project and decide to put away personal opinions and instead decided "that the sum is greater than it's parts"

(As a side note, if you have not, I would highly suggest looking into Es Devlin's work. It has absolutely inspired me and made me think much more about set design.)

Bold As Love

When I began this blog I had every intention of writing about the moving truss that was used in the process of recording John Mayer's live DVD "Where the Light Is." What started as innocent research was quickly overtaken by reminiscing about the goodness that was/is The John Mayer Trio. Not only the trio in and of itself but the perfect symmetry of the stage that lead to a very well lit song. Prior to where this particular video begins we find each member of the band being highlighted by plain white light with some minimal crowd lighting as Mr. Mayer introduces the song. Not even two words into the song, the house lights dim completely leaving a spotlight and yellow wash backlight only on the main attraction. As the rest of the band comes in we see their spotlights dim up so that they are now included in the show. The dominant colors during the verses is yellow. It keeps the energy of the song up without being too overpowering. There are some minor reds and blues thrown in. With the blue being used to accent a small instrumental between the chorus and verse 2. After the second chorus Mayer launches into a solo which is accented by some minor dimming effects from the back of the stage and some sweeps of the lights across the audience. The most impressive part of the design here to me is what happens after the solo. Post solo the band bring things down a little bit. Perfectly on cue with a snare hit the lights go from yellows and red to purple and blue, bringing the mood down perfect for John to do a little talking. Going back into a solo after he's done talking we see more red introduced into the mix of purple and blue then once he begins singing again they bring up the bright yellow which was used throughout the first verses and choruses. Watching this performance really makes me think about how important the usage of colors is. Every color used here highlights the part of the song that it appears in perfectly. It makes sense. The listener/viewer is taken on a journey with the lights simply with the use of color and some minor dimming and sweeps. There are no major strobes or anything too flashy. A lot of the things that I notice in the video are things I wouldn't have necessarily thought about before having taken classes on lighting. But now that I have that knowledge all the choices that the lighting designer made here make perfect sense. For me this is just an almost perfect example of how lights and music can meld together so well. When they compliment each other it enhances the experience that much more. Biggest take away for me from this performance is, colors matter. Use them wisely. Know where the band is trying to take the audience and help them lead the way with light.

Girl Talk

This week will be yet another review/breakdown of a recent concert that I've seen. This past weekend I had a chance to see Girl Talk. Though most people would define Girl Talk as just a glorified DJ, he considers himself an electronic musician. His creates his music by combining samples of many different kinds of music. He does all of this with ease and combines the ultimate party mix. His music lends itself best to large music festivals though he is completely capable of touring on his own and drawing large crowds. The last few times I have seen him his production has gotten increasingly better with this weekend being some of the best production I've seen. Across the front of the stage he had three LED screens on the front of rolling tables. The middle table was where he stood and did his mixing. On top of the LED screens on stage left and stage right were an LED mover, I'm guessing the Martin 101 or 301, and a crowd flasher. (Not sure of the correct terminology for "crowd flasher") On the upstage edge were three more LED displays in deformed plus shapes. Underneath these displays were three high-powered strobes and two moving head lights. There were also LED movers on top of these displays. The LED displays were not used for IMAG but rather were used for some random animations. Some of the animations related directly back to the music and the samples being used but the majority of the time they were flashing random "Girl Talk" logos or just completely random pictures. Somehow amongst the randomness of the images though, they fit perfectly with the party atmosphere that was present at the show. One mystery about the show that I am trying to solve is how the Lighting Designer or Video Director is able to match up the animations that correlate to the show at the right time. Everything that Girl Talk does he mixes live so it seems improbable that the planned parts of the show are just lucky cue hits. Many of the lighting cues are tempo dependent and fall perfectly on drums hits etc. The answer could simply be that the "live mixing" is a facade and every minute of the show is planned to a tea, but I've seen him many times and each time the mixes have been don differently. It could be a usage of MIDI triggers of some sort or it could be just great planning. Whatever it may be, the show flow seamlessly between chaos and order. The balance between chaos and order is what makes the show work. Yes there is a high level of production. But at the same time it all feels like it's flying by the seat of its pants. If the show swayed too far on the side of production I think it would fail. If it was too chaotic it would also fail. Girl Talk seems to have found the perfect balance and continues to explore different lighting and video technologies that will enhance his show. In talking about finding the balance between chaos and order makes me think about my own programming and how important it is to be creative and smart with your lighting decisions. Too many effects and strobing could really fatigue your audience and turn them off to a show, but too little could disengage the audience and leave them bored. (photo courtesy of http://sunfest.com/blog/girl-talk/)

MUTEMATH at the House of Blues Orlando

A couple of months ago I had the opportunity to see one of my favorite bands MUTEMATH play at the House of Blues here in Orlando. In watching some interview with the band before seeing them they said that this was going to be one of the most production heavy tours that they had ever done and the concert did not disappoint. MUTEMATH is a four piece rock band that plays rock with an electronic edge that is all in a well seeded groove. The main attraction at the show was a set piece that sat behind the band that was used for the 3D projection mapping. The mapping wasn’t as advanced as I was hoping, but definitely added a lot to the show. It’s amazing how much more immersive a show can be when you add in a giant screen in the background of a band in addition to all of the lights. The projection sometimes acted as just a giant light. It was used for IMAG at times as well though. What I found most impressive was the integration of lighting and projection into the show. The screen, which was in a stair step shape leading up to a point and then back down from left to right, had an LED fixture on top of each “step” along the way. These fixtures were moving head lights so they could be pointed at the audience, used to highlight the individual band members or just pointed and moved to add excitement to the show. In addition to the fixtures along the screen there were also about six of the same fixtures stair stepped on road cases on either side of the stage. In a similar manner as the lights on the screen the fixtures on the sides were most often pointed in and used for strobing effects during drum break downs or other parts of the songs. The colors that the LEDs were able to produce were unbelievable. I feel confident in saying that these lights produced some of the richest hues that I’ve ever seen at a live show. When all of the LEDs were combined together either in motion or just in color it created a look for each song that really helped to visualize the music. I would go so far as to say that this show may have been one of the best lit shows I’ve ever seen. I've included a video of a short portion of the show. I apologize that my phone does not do the audio justice, however, even with the video muted I think you can get a good idea of the visual effects of the show.

In the future...there are no consoles

http://www.prosoundweb.com/article/going_mobile_the_2_pound_72_channel_wireless_console/ It is somewhat difficult to imagine a future in the audio industry either working FOH or Monitors without a console and splitter box or one of the staples of the audio system setups of today but this is just what Bob Lentini has done. He has introduced a new system for mixing live sound that does all of its mixing from a single computer. Bob Lentini is the brainchild behind the S.A.C(software audio console) a 72 input, 72 output virtual front of house console that runs off of a Windows PC. It should be added that according to the article the sound quality of one of these systems matches, if not bests, that of a high end digital console and comes very close to reproducing the quality of analog sound. All of this is achieved at a fraction of the price of many of the digital consoles in use in the market today. One of the things that allows the SAC to operate so well is its use of assembly language. As I understand it, assembly language is very close to binary language, or machine language as opposed to C++ which requires a lot of decoding by the computer. Because SAC makes use of assembly language it is able to operate much quicker than many of the computer softwares on the market today that deal with audio. Because it can operate much quicker it is able to do more complex conversions of digital to analog sound thus resulting in a high sound quality. Another incredible thing about this system is that once you purchase the software it is something that could be assembled entirely by the user. The SAC website has a step by step guide that takes one through the process of building the computer and the input rack. With the introduction of tablets and wireless computer systems into front of house mixing it is allowed the front of house engineer to be completely mobile while building a mix for the audience. The SAC continues this trend with the only exception being that there is no console still sitting somewhere in the middle of an arena. The size of the SAC and inputs and outputs is quite small which frees up room for more seats which ultimately means more money for a venue and for an artist. While the system can be mixed remotely it is not dependent on the remote mixer in order to operate. If the wireless signal were to go down between the tablet and the SAC the SAC would continue to operate at whatever levels were previously set. It is quite possible that what we have in the SAC is a glimpse of the future without large audio consoles. At this time it’s almost impossible to see this happening, but over the next few years if this technology can prove to deliver a great sound at a lower cost and a better efficiency we may just see some of the larger console manufactures scrambling to keep up with this small company.

Audio Coverage

http://www.prosoundweb.com/article/the_big_5_how_to_illuminate_the_audience_with_beautiful_consistent_audio_co/P1/




1. Provide even sound coverage of all audience.
2. Provide adequate loudness before distortion.
3. Provide adequate loudness before acoustic feedback.
4. Be easy to understand.
5. Reproduce musical sources with adequate clarity and fidelity.

These are the “Big 5” rules of sound as outlined by Pat Brown. At first glance it may not seem so impossible to follow these rules, but when one begins to see that all 5 of these rules must be followed simultaneously it begins to seem not quite as easy. There are plenty of rooms that meet the requirements of two or three of these rules at a time, but it can sometimes be hard to find a room that will meet all five.
I know for me personally, many of the rooms I grew up playing music in and mixing in at my church barely met these rules. The rooms very rarely were actually built for music and the couple of rooms that were built with music and speech in mind were very spotty in terms sound coverage.

In the article comparisons were drawn between a lighting designer and a sound system designer. Similar to the ways that a lighting designer has to make sure that his light covers the stage evenly and completely, it is the job of a sound designer to make sure that his speaker choice at the distance they are away from the audience project sound evenly and completely. Brown translates this to terms of directivity, defining directivity as, the two variables that determine coverage: distance and coverage angle.

According to Brown, the larger a speaker is the more directivity it will have.
So if a speaker is to be far away from an audience it must be large enough to cover that audience with sound, however the closer a speaker is to an audience the smaller it can be to provide the same amount of coverage. This is not always an option as sometimes the person for whom you are designing a sound system might have strict requirements on where speakers can be placed. If this is the case it is important that one knows their room and takes the time to listen to the speakers in the room to determine if coverage is good or not. The problem comes when someone wants a small loudspeaker far away from the audience. It would be very hard for a sound designer to follow the “Big 5” with these kinds of restraints put on him.

Brown suggests that in order to ensure the best coverage one should hire a sound specialist that is equipped with the tools needed to measure sound coverage so as to get the best sound out of their system as possible. He suggests that one do it this way since the tools needed to measure sound coverage are often very expensive to acquire and it would be more cost effective to just hire someone to do the job.

U2 360 Tour

http://www.prosoundweb.com/article/u2_360_redefining_stadium_sound_in_the_round_on_current_tour/

I had the opportunity to see the U2 360 tour in Atlanta, GA. At the time I was very aware of the technicality of the show however I did not have the knowledge to understand it to its fullest extent, that and the scope of the concert itself put any technical thoughts out of my mind and just left me to enjoy and appreciate the music.
After being at Full Sail for a year, circling back around and reading up on technical details of the tour and show is very eye opening and somewhat unfathomable. Sitting in class today we were discussing the decibel, different measurements, power needed to produce certain decibels and minor discussions of amps. Looking back on today’s lecture in class and how all of that info would apply to something like the “360 Tour” helps me to see just how important this math can be.
If my understanding is correct the total number of speakers including subs, but not including delays, comes in at 376. U2 has had a long relationship with Clair and used the newer i-5 line source array system for this tour. Because the tour is done in the round the setup required rear hanging fills and side hanging fills were needed instead of just the typical speaker setup. There were also front fills needed on the stage level for those that were standing in the general admission section that was right next to the stage.
Typically where there are speakers amps are also required to power those speakers. The article says that for this tour Clair used the largest number of amplifiers that they have ever used for a tour. Over 180 Lab.gruppen amps were needed to power the large system.
Going back to my comment about the importance of math and calculations that such a tour would require, it turns out that Clair’s AlignArray software was used for this tour. This software was designed specifically for use with the “i-series” of speakers used on the 360 tour. The software handles everything from designing the system and how it will be flown to understanding the coverage that the system will produce. I’m sure using this kind of software is much easier than sitting down and working through math equations for hours at a time, however knowing the equations and what makes everything work the way it does would surely be helpful.
From beginning to end the U2 360 Tour was meticulously designed so that all parts of the production would work without a hitch and provide the concert-goer with the level of excellence that they would expect from a U2 show.

Comment for This Week

This week I commented on my friend Chris's blog about the rubber mat outside his door- check out his blog here

Bar Lights Setting the Mood

A little late getting this post up, but I thought it was cool all the same. This is a picture that I took of a bar in downtown Winter Park on Tuesday night. I don't remember the name of the restaurant, but it is at the very end of Park Ave. and usually has live music in the form of a piano player. There were a couple different cool things going on with the bar light wise. The bar itself was the only one I was able to get a picture of though.

These amber bar lights created great accents for the bar while keeping the mood relaxed and chill. They were not very bright, by no means were they the main light source in the bar, but they really did a good job keeping things near the bar well lit. I feel like often times restaurants and clubs go too far with the mood lighting and keep things really dark, which can be cool I guess but it's not very cool when you're trying to sign a receipt or have a face to face conversation with the people you are with. There is a time for moody, dark lighting, but if you go to far it just gets dark and annoying. This light(similar to the Dave and Buster's one over our table) is another one that I'm not quite sure of how it works. The light was brighter in some areas than others so maybe it's a few single bulbs spread out throughout the bar illuminating the glass from behind. Either way I thought it was a great accent to the bar.

In addition to these lights in the bar itself, the bar had some lights shining on the area behind the bottles. The lights had a gobo in them that sort of looked like water and it was swirling while also changing colors. When I first looked at the wall I was baffled as to how they were achieving that effect, but then I thought on my feet and looked up. Sure enough just a few feet in front of the wall were two fixtures. I think that they were Martin's, but I could not make out the serial # or model #.

Overall it was just cool to see creative use of lights in a restaurant. It makes me wonder how many restaurants take lighting into account when designing their space and if they do design with lighting in mind where it typically happens. Do they include lighting ideas from the very start or is the lighting an afterthought? Quite honestly, I would hope that it would be one of the first things they think about as the lighting of a restaurant can play a huge part in the appetite of your customers.

Dave & Buster's Part 3

So in my final post about Dave and Buster's, I would like to point out a strange thing I noticed about their regular fixtures throughout the gaming area. In the picture you can see what appears to be a pinkish colored light. I did not notice this until we were leaving for the night, but these fixtures were all throughout the gaming area. These lights were hung all throughout the ceiling. To be honest, I cannot think of a reason why they would be pink. I know it probably has something to do with how pink light makes everything else look, but my brain was having trouble grasping exactly what pink light would do to everything around it. Would love to hear some thoughts on why Dave and Buster's would use this color light. Leave me a comment, let me know what you think.

Dave and Buster's Part Deux

In my last post I discussed the dining area of Dave and Buster's. In this post I'd like to discuss the overwhelming amount of lights found in the gaming area.

The games area a of D&B is almost sensory overload. Almost everygame on the floor has some sort of flashing lights begging for your attention. Chasers, blinkers, LEDs, conventionals, you name it, they're most likely on an arcade machine somewhere throughout the giant arcade/restaurant. None of these lights are focused on anything particular. They're only focused on grabbing the attention of D&B customers.

The lights were overwhelming at first. When the lights were combined with loud music, arcade game noises, and lots of people walking around it was enough to drive you crazy at first. (Luckily though, after being their for a little while my eyes became used to the barrage of light.)

I took a quick video, because the picture doesn't quite do it justice. The video doesn't quite capture the overload of lights as I first experienced it though.

Dave and Buster's Part 1

Last night I went to Dave and Buster's and as I'm sure you can all imagine the amount of light things going on there was insane. Pretty much every game in the place has a flashing light of some sort, so there was a lot to take in. I'll be splitting my findings there into three parts.



For this first part, I'd like to focus on a light that was actually above the table while me and my friends ate. There was one of these fixtures above every table in the dining area. What I found so fascinating about the light was that it illuminated the table and yet was still a very soft light. The material that the fixture was made out of was also fascinating. The blue cylinder inside of the light was glowing, but it was not letting out so much light that none escaped out of the focus point on the bottom of the cylinder. Because of the soft tones of the light, it made me feel relaxed and it gave a nice contrast to all of the flashing lights in the gaming area.

My classmate Troy has a great sunset picture here

The Four Become One

I was at a friend's house last night just hanging out enjoying some coffee when I looked above their kitchen table and noticed an almost perfect circle of light above their chandelier-ish style lights. Upon further inspection I noticed that there were four individual lamps arranged around the fixture each covered with a shade. The shade on each of the lamps had a small hole at the top, so not only was the shade directing light back down onto to the table, but it was also allowing a small amount of light to escape out the top. The circle on the ceiling was not perfectly focused, it had soft edges and some chain shadows in it, but overall I thought it pretty impressive that the light made that shape on the ceiling. Without the things that I've been learning in class I probably never would have observed this or paid any attention to the lights in this way.

My Friend Justin, Half-Lit

So I was sitting in lab tonight when I looked over and noticed that Justin was almost perfectly half lit by the light coming out of the closet. We had the lights off in the room as it was that we were each taking turns setting cues, making groups, and experimenting with the lights, so the room was kind of dark all in all. The light that is illuminating half of Justin's face and body is coming from two fluorescent bulbs on the ceiling of the closet. This light was meant to be focused to light up the closet and it's contents but in the darkness of the room and with it's escape out of the doorway it was a great source for some cool lighting.

Blinds Effect

I was just watching a movie at my friend's apartment and noticed that her light on the front porch caused a cool shadow on the wall through the blinds in her front window. I didn't have a lot of time to analyze exactly what was causing the effect because we were watching a movie. However it was quite interesting, the shape was almost a semi-circle of individual lines of light. As best I could tell it was the angle that the light was coming in combined with the placement of the blinds in relation to the wall that caused the shadows to be cast and the light to be let through in the way that they were.

Things are strange at 6 a.m.

So, I was walking into my apartment this morning very early and saw this light in the distance. If you look up and to the right of the lamp in the parking lot, you will see a glow coming out from behind the trees. The picture did not come out as well as I hoped, but my explanation can maybe do it justice. I'm guessing that it was some kind of construction project going on as the light was very white and somewhat dusty. I know work lights are typically very, very bright. The way the light was shining it almost created a bubble like focus over the area. Honestly, it was a little bit crazy looking, but doesn't everything look a little crazier at 6 in the morning?

Natural Light in My Room

I noticed this morning when I woke up how strange it was that the sunlight was illuminating my whole room. My blinds are closed and yet somehow the light snuck around my blinds and through them and woke me up. Strangely though, around 9:30 this morning there were no shadows cast of the blinds on any of my walls, only the pure light that made my plain white walls shine.

Kitchen Light

There's a light in my kitchen that is on the ceiling. It always seems to put out just the right amount of light for whatever I need. It fully illuminates the kitchen area in my apartment, but since my apartment is very open, the light spills into the living room and dining nook very easily. The light is directly above the sink. Shadows are cast from the bar stools on the other side of the sink/counter and you can see the light dissipate as it goes across the walls towards the living room. Whenever I come in to my apartment this is typically the first light that I turn on because it is just bright enough to make almost everything in my apartment visible.

Sometime's It's Nice To Know Someone's Home

When I moved down to Full Sail I moved in with a roommate whom I had never met before. We are in different degree programs and we only really hang out on the rare occasion when we are both in the apartment at the same time, but there is something reassuring about walking in at night and seeing the light on in his room. Sure, he may be asleep already, but it's nice to know someone else is there. The light comes out his door and spreads onto the blinds of the window in the living room area, but dissipates quickly, not quite lighting up the whole living room/dining room/kitchen area. It's just enough light to let me see what's going on in the apartment when I walk in. The light is not natural, but is created by a lamp in his room. It's not focused anywhere particular in his room except up so as to try and light all of his room. The light that escapes out of his door is simply leakage and is in no way planned to help illuminate my steps as I come into the apartment. It's a faint light, not too warm, not too bright, but it's there and that's good enough for me.

Light of the Morning

On the morning's that it is sunny outside, this shadow is created directly outside of my apartment door. When I see the shadows it typically is a sign that the day is going to be a great one, because the sun is shining and that means the weather will be good and when the weather's good everything else in the day just seems to feel a little better. The sun casts a perfect shadow of the guardrail on the ground. The slits and poles of the guardrail are outlined almost perfectly. In addition to that, this is usually the first natural light I see in the day. Sure, a little bit of light may creep in through my blinds, but that light is almost always met with disgust, where as the light that falls outside my door is a sign that the day might not be so bad after all.